From c8b273c80abe98e53828f46079a187975938a56a Mon Sep 17 00:00:00 2001
From: Private Island Networks <opensource@privateisland.tech>
Date: Mon, 1 Sep 2025 12:34:17 -0400
Subject: rename source to src

---
 source/mdio_data_ti.v | 128 --------------------------------------------------
 1 file changed, 128 deletions(-)
 delete mode 100644 source/mdio_data_ti.v

(limited to 'source/mdio_data_ti.v')

diff --git a/source/mdio_data_ti.v b/source/mdio_data_ti.v
deleted file mode 100644
index aef537d..0000000
--- a/source/mdio_data_ti.v
+++ /dev/null
@@ -1,128 +0,0 @@
-/*
- *   mdio_data_ti.v  ( TI DP83867 PHY )
- *
- *   Copyright (C) 2018, 2019 Mind Chasers Inc.
- *
- *   Licensed under the Apache License, Version 2.0 (the "License");
- *   you may not use this file except in compliance with the License.
- *   You may obtain a copy of the License at
- *
- *       http://www.apache.org/licenses/LICENSE-2.0
- *
- *   Unless required by applicable law or agreed to in writing, software
- *   distributed under the License is distributed on an "AS IS" BASIS,
- *   WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- *   See the License for the specific language governing permissions and
- *   limitations under the License.
- *
- *	function: MDIO ROM for TI DP83867 PHY 
- *	
- */
-
-
-
-`timescale 1ns /10ps
-
-module mdio_data_ti #(parameter ADDR_SZ = 7)
-(
-	// params that alter the data returned
-	input [4:0] page,
-	input [4:0] reg_addr,
-	input [7:0] data_in_h,
-	input [7:0] data_in_l,
-	
-	// ROM interface
-	input oe,
-	input [ADDR_SZ-1:0]ad,	
-	output [7:0]d
-);
-
-localparam R = 8'h20;
-localparam W = 8'h00;
-localparam EOP = 8'h80;
-
-localparam REGCR = 5'h0d;
-localparam ADDAR = 5'h0e;
-
-reg [7:0]data;
-
-assign d = oe ? data : 8'hzz;
-
-// register 22 is page       
-always @ (*)
-begin
-	case (ad)	
-		/* 
-			Subroutine: SGMII Init ( i ) Not Needed for TI PHY, but read PHY Control Register (PHYCR), Address 0x0010
-		*/	
-		
-		// read the PHYCR register, SGMII Enable is bill 11
-		0: data = R|8'h10;		// pg 18, reg 20
-		
-		/* 
-			Subroutine: Read Live Status ( s )
-		*/
-		// read the live copper status PHYSTS (0x17) 
-		20 : data = R|8'h11;	// read addr[17]
-		
-		/* 
-			Subroutine: Dump Registers 0:3
-		*/
-		25: data = R|8'd0;
-		26 : data = R|8'd1;
-		27 : data = R|8'd2;
-		28 : data = R|8'd3;
-		
-		/* 
-			Subroutine: : Loopback ( 0_0.14 )
-		*/
-		40 : data = W|8'd0;				// write addr[0]
-		44 : data = 8'b01000000;		// collision, speed select, reserved
-		45 : data = 8'b01010001;		// reset, loopback, speed, AN enable, power down, isolate, restart AN, duplex;
-		
-		// read it back
-		46: data = R|8'd0;
-		
-		/* 
-			Subroutine: : Read a register.
-		*/
-		48: data = { 3'b001, reg_addr };
-		
-		/* 
-			Subroutine: : Write a register.
-		*/
-		50: data = { 3'b000, reg_addr };
-		51: data = data_in_l;
-		52: data = data_in_h;
-		// read it back		
-		// 53: data = { 3'b001, reg_addr };
-		
-		// y: extended read
-		60: data = {3'b000 , REGCR };		
-		61: data = 8'h1f;
-		62: data = 8'h00;
-		// Write the extended address to 0xe
-		63: data = { 3'b000, ADDAR };
-		64: data = data_in_l;
-		65: data = data_in_h;
-		// Write 0x401f to 0xd
-		66: data = { 3'b000, REGCR };
-		67: data = 8'h1f;
-		68: data = 8'h40;
-		// Read value in extended register: read 0x0E
-		69: data = { 3'b001, ADDAR  };		
-		
-		// z: extended write
-		// Write value in extended register: 0x0E
-		80: data = { 3'b000, ADDAR };
-		81: data = data_in_l;
-		82: data = data_in_h;
-		// read it back		
-		83: data = { 3'b001, ADDAR  };
-		
-		default: data = R|EOP;
-	endcase
-end
-
-endmodule
-	
-- 
cgit v1.2.3-8-gadcc